OUR SHOP IS ON VACATION UNTIL FEB 11th.
You may still order online or by phone but please understand that orders
will be filled soon after Feb. 11th. Thank you.
FREE* DOMESTIC SHIPPING W. CLUB ORDERS
OVER $149--48 State region
SHIPPING COSTS WILL BE REMOVED WHEN ORDERS ARE FILLED.
* DOMESTIC SHIPPING FOR
TOUR EDGE JMAX QL IRONWOODS IS INCLUDED IN THE SET PRICES. NO FURTHER
DISCOUNT PERMITTED.
Here are some of the NEW
Easier-to-Hit Hybrid Irons that will replace your hard-to-hit
irons. Hybrid irons provide the playability of a fairway wood
coupled with the accuracy of an iron. They are used anywhere irons are used.
You can expect better trajectory, more consistency, and at least the distance
(usually more) of a well struck iron of the same loft.
NOTE:
It should be noted that the 3 and 4 irons, whether they are hybrid irons or std.
irons, are not expected to yield the distances of any 3, 4 or even 5
wood. A good rule of thumb is that an iron numbered about 4 less than the fairway
wood should yield similar distances to that wood. That is, a 1 iron is approximately
equivalent to a 5 wood and a 5 iron is about equivalent to a 9 wood.
SHOULD I SWITCH TO THE NEW HYBRID IRONWOODS?
1. If you feel more confident hitting higher lofted fairway woods
than irons, or
2. you don't use your #3, #4, #5, or even your 6 iron any more,
or
3. you can get more distance from a 9-wood than a
5-iron, or
4. you seldom take a divot
when hitting your middle irons, or
5. you have even considered carrying woods like the
#11 or #13,
then Hybrid
Ironwoods may be the Answer to Better Golf Shots.
Consider either the new Avatar, Silver Diamond T Series RM5, iDrive
ironwood, the Titan Plus, the Tour Edge Imax Iron-woods, Power Play System Q
Adrenaline Ironwoods, or the Power Play Select 5000 Hybrid
Ironwoods below. All are GREAT to hit and are all available in iron lofts from #3 -
PW and some offer AW, SW and even LW.
AT CMC GOLF CLUBS, ALL CUSTOM ASSEMBLED HYBRID
SETS ARE MADE WITH FREQUENCY MATCHED SHAFTS AND SWING WEIGHT MATCHED FOR BETTER
PLAYABILITY AND MORE CONSISTENT PERFORMANCE.
NO EXTRA CHARGE FOR THIS SERVICE.
Definitions of head dimensions:Face
Length is along hitting portion;
Face Height is the slant measurement up the face;
Girth is distance around the fat portion of the head.
*NEW for 2011*
System Q Adrenaline Ironwoods
This new Power Play System Q Adrenaline ironwood
has a complete makeover.
New iron-like scorelines pattern and groves.
Improved weight distribution and a slightly larger
head than the PP Select 5000.
Unique unirail sole to efficiently get through any
lie.
Available in RH with lofts #1-9, PW, SW
These ironwoods are EASY-TO-HIT with good accuracy
and impressive distance.
Made with 431 stainless steel.
Square face angles
Std. Iron lengths
Custom assembled with many steel and graphite
shafts available as well as grips.
Recommended shafts are:
Apollo Acculite steel (93grms) or the high modulus graphite shafts like
the iDriver filament wound shafts.
CALL to order loft combinations or shaft/grip
combinations not listed below:
Sale priced
from only $33 each for completely assembled
individual club with
std. steel shaft and $39 with
iDrive graphite or Apollo Acculite steel.
ADD VERY NICE SLIP-ON HYBRID COVER
set w. zippers
#3-PW, SW. ONLY $20 for the set. CALL TO ORDER the COVERS.
Call 970-209-6502 Cell
or 970-641-3822 to
order. or order securely below:
ORDER Custom Assembled
System Q Ironwood Sets
(example: 5 with standard steel shafts)
for only $150.
Save by ordering 5 or more
#1
#2
3
4
5
6
7
8
9
PW
SW
Loft (º)
15
18
21
24
27
30
34
38
42
47
52
Lie (º)
60
60.5
61
61.5
62
62.5
63
63.5
64
64
64
Wt.
228
235
242
249
256
263
270
277
284
291
298
Offset
2mm
1.5
1
0.5
0
-1
-2
-3
-4
-4
-4
ORDER Custom Assembled
System Q Ironwood Sets
(example: 5 with graphite or Apollo Acculite shafts)
for only $175.
Heater III Super Launch Ironwood
20% OFF SALE
Very Popular Ironwood
Heater III SL hybrid ironwoods are available in the
stronger iron lofts from RH only: #2,
15º; #3,
18º, ..., #9, 39º, PW 42º, SW
45,
in 3 deg. increments.
Wider body promotes more confidence at setup.
Shallow face made from 17-4 stainless steel for more explosive
initial ball velocity.
Custom assembled with many shaft and
grip options.
Recommended shafts are
Recommended shafts are:
Apollo Acculite steel (93grms) or the high modulus graphite shafts like
the iDriver filament wound shafts.
Order any combination of lofts.
Sale priced from only $34
each for completely assembled individual club with std. steel shaft.
ORDER Custom Assembled
Heater III
Ironwood Sets (Example: 5 with std. graphite shafts)
for only $185.
Call 970-209-6502 Cell
or 970-641-3822
to order.
ADD VERY NICE SLIP-ON HYBRID COVERS w.
TAGS:
#3-PW, AW, SW. ONLY $5 ea. WHEN ORDERED WITH
AN IRONWOOD SET. CALL TO ORDER the COVERS.
iDRIVE Hybrid Ironwood
20% OFF SALE
Our 2nd Most Popular Ironwood
iDRIVE hybrid ironwoods are available in the
stronger iron lofts from RH & LH #3,
19º to
PW 43º, SW
46,
in 3 deg. increments.
Wider body promotes more confidence at setup.
Shallow face made from 17-4 stainless steel for more explosive
initial ball velocity.
Custom assembled with many shaft and
grip options.
Recommended shafts are
Recommended shafts are:
Apollo Acculite steel (93grms) or the high modulus graphite shafts like
the iDriver filament wound shafts.
Order any combination of lofts.
Sale priced from only $33
each for completely assembled individual club with std. steel shaft.
Measurements
Face Length
Face Height
Girth
#6
3.25"
1.2"
6.75"
#9
3"
1.4"
6.6"
Call 970-209-6502 Cell
or 970-641-3822 to
order if desired.
BELOW, ORDER Custom Assembled
iDRIVE
Ironwood Sets (Example: 6 with std. steel shafts)
for only $180.
ADD VERY NICE SLIP-ON HYBRID COVERS w.
TAGS:
#3-PW, AW, SW. ONLY $5 ea. WHEN ORDERED WITH
AN IRONWOOD SET. CALL TO ORDER the COVERS.
CALL FOR INFORMATION AND PRICES FOR ANY TOUR EDGE PRODUCTS
TITAN PLUS by SVG
20% OFF SALE
OUR BEST SELLER since last Sept.
PERFECT
SIZE IRONWOODS!
Titan Plus Ironwoods are extremely easy to hit long and
straight.
Face material is the harder 15-5 stainless steel for
more explosive solid hits.
Face heights get progressively larger through the SW.
Available in RH and LH lofts: #3 (19º) - PW (46º), AW
(51º), SW (55º).
Minimal offsets of 4 mm in #3 to 0 mm in PW.
Easy to hit from all lies and off the tee.
CUSTOM ASSEMBLED. Many shaft options.
Recommended shafts are:
Recommended shafts are:
Apollo Acculite steel (93grms) or the high modulus graphite shafts like
the iDriver filament wound shafts.
Special set prices from
$155 for any 5 Titan Plus Hybrid Ironwoods
assembled with
std. steel shafts; or $190 with graphite shafts.
Individual assembled Titan
Plus ironwoods priced from $33 each with std. steel shaft.
No.
3
4
5
6
7
8
9
PW
AW
SW
LW
Loft
19
22
25
30
34
38
42
46
51
55
60
Lie
59.5
60
60.5
61
61.5
62.5
63
64
64
64
64
F.A.
0
0
0
0
0
0
0
0
0
0
0
Wt.
231
238
254
261
267
274
281
288
294
300
305
BELOW, ORDER
Custom Assembled Titan Plus Hybrid Sets of 5 or more from $190 with graphite.
System Q Sets with better quality shafts
Shaft Flex desired
Grip Choice
Club Lengths
Choose your shaft type
Tell us the Club Numbers you want
Questions or comments?
VERY NICE SLIP-ON HYBRID COVERS w.
TAGS:
#2-PW, AW, SW. ONLY $5 ea. WHEN ORDERED WITH
AN IRONWOOD SET.
To order a set different from
what's listed in the online ordering below or to order LH Titan Plus Ironwoods, please
call us.
CALL TOORDER
Custom Assembled Individual Titan Plus Hybrid Ironwoods from $33ea. Add the
very nice Head Covers to your Titan Plus order for our cost of $5 each.
Call 970-209-6502 Cell
or 800-218-4808 to
order.
LH NOW AVAILABLE
Below #3-6
Below #7-PW
Measurements
Face Length
Face Height
Girth
#6
3"
1.25"
6.33"
#9
3"
1.75"
6.33"
BELOW, ORDER
Custom Assembled Titan Plus Hybrid Sets of 5 or more from $155 with steel.
Titan Plus Sets with steel shafts
Shaft Flex desired
Grip Choice
Club Lengths
Tell us the Club lofts (#) you want
Questions or comments?
NOTE: Apollo Acculite steel shafts
will substitute the iDrive graphite shafts at the same price.
Call 970-209-6502 Cell
or 970-641-3822 to
order if desired.
To Order
Titan Plus head sets of 5 or more starting at $90, CALL.
Order individual Titan Plus heads at $20.00 each.
*New 2007*
ACER XDS WIDE SOLE HYBRID IRONWOOD 20% OFF SALE
FOR SHANKERS OR
HOOKERS
FACE-FORWARD DESIGN--REVERSE
OFFSET
CUSTOM ASSEMBLED. Many shaft options.
Recommended shafts are:
Apollo Acculite steel
(93grms) or the high modulus graphite shafts listed. Call for other shaft options
not listed in the order section.
No.
2
3
4
5
6
7
8
9
PW
SW
Loft
19º
22º
25º
28º
32º
36º
40º
45º50º
55º
Lie
58º
59
60
61
61.5
62
63
63
64
64
Wt.
237g
244
251
258
265
272
279
286
293
300
Offset
-10mm
-12
-14
-16
-18
-19
-20
-21
-21
-21
CALL TO ORDER
Do you have a tendency to shank
your irons? Then these hybrids are for you.
The Acer Wide Sole hybrids have a
progressive face forward design--a
reverse offset from 8mm to 21mm (PW).
Head width is approx. 30% wider
than typical ironwoods. Their design is based on small fairway
woods.
Head volumes from 160cc (#3) to
104cc (PW).
Two sole rails help power through
the grass and prevent digging.
Higher launch angles from the
rearward center of gravity.
Lofts are about 3 deg higher than
std. iron lofts.
RH only. #2 - PW, SW.
See table to the left.
Recommended shafts are:
Apollo Acculite steel (93grms) or the high modulus graphite shafts like
the iDriver filament wound shafts.
CALL to
Order Individual ACER XDS IRONWOODS at $35 each.
Measurements
Face Length
Face Height
Girth
#6
3.75"
1.4"
6.8"
#9
3.75"
1.7"
6.8"
NOTE: Apollo Acculite steel
shafts will substitute the iDrive graphite shafts at the same price.
Call 970-209-6502 Cell
or 970-641-3822 to
order if desired.
New T Series RM-5 provide more distance
while being easier to hit than traditional irons.
They unite a higher moment of inertia than long irons
with a low and deeper center of gravity.
Thus the RM-5 combines maximum forgiveness on miss-hits
with a higher launch angle and high spin so shots stop quickly.
Face material is 17/4 stainless and black enamel body
color.
Uniform face heights thru #9. Head size similar
to PP Sel. 5000 hybrid iron below, but with a slightly wider head.
Stronger iron lofts from #2 (16º) to PW (41º) for RH
and #2 - #5 in LH. See table below.
CUSTOM ASSEMBLED. Many shaft options.
Recommended shafts are:
Apollo Acculite steel (93grms) or the high modulus graphite shafts like
the iDriver filament wound shafts.
Shaft lengths are
+1/2" longer than the std.
irons they replace.
CUSTOM ASSEMBLED set prices from
$160 for any 5 RM-5 Hybrid Ironwoods with
steel shafts; $190 with graphite.
Individual RM-5
ironwoods priced from $34 each.
To order a set different from what's listed
in the online ordering below or to order LH RM-5 Hybrids, please phone us.
No.
2
3
4
5
6
7
8
9
PW
Loft
16º
19
22
25
28
31
34
37
41
Lie
58.5º
59
59.5
60
60.5
61
61.5
61.5
62
F.A.
0º
0
0
0
0
0
0
0
0
Wt.
230g
237
244
251
258
265
272
279
286
BELOW ORDER
Custom Assembled RM-5 HYBRID SETS from $180 (6
clubs) with steel, just $30 each
RM-5 Sets with steel shafts
Shaft Flex desired
Grip Choice
Club Lengths
Tell us the lofts (#) desired
Any questions or additions?
NOTE: Apollo Acculite steel
shafts will substitute the iDrive graphite shafts at the same price.
CALL TO ORDER
Call 970-209-6502 Cell
or 800-218-4808 to
order.
Measurements
Face Length
Face Height
Girth
#6
3"
1.15"
5.75"
#9
3"
1.2"
5.75"
BELOW ORDER
Custom Assembled RM-5 HYBRID SETS for $190 (5
clubs) with graphite, just $38 each.
ADD
A VERY NICE SLIP-ON HYBRID COVERS w.
TAGS:
#2-PW, AW, SW. ONLY $5 ea. WHEN ORDERED WITH
AN IRONWOOD SET.
RM-5 Sets with better shafts
Shaft Flex desired
Grip Choice
Club Lengths
Choose shaft type
Include any questions or additions
ORDER
Custom
Assembled Individual RM-5 HYBRID Iron/woods with steel from $34ea.;
with graphite, $40ea. below:
Call 970-209-6502 Cell
or 970-641-3822 to
order if desired.
POWER PLAY SELECT 5000 HYBRID IRONS
20% OFF SALE
**SPECIAL SET OFFER BELOW**
LH Available #1 - 9, PW, SW
CALL to ORDER LH
BELOW,
ORDER Custom Assembled Select 5000 Ironwood Sets of 6 or more from $150 with steel.
Select 5000 Sets with steel shafts
Shaft Flex desired
Grip Choice
Club Lengths
Tell us the Club Numbers you want
Questions or comments?
NOTE: Apollo Acculite steel shafts
will substitute the iDrive graphite shafts at the same price.
CALL to ORDER INDIVIDUAL PP SELECT 5000 IRONS,
ASSEMBLED, from $25 with std. steel shafts or $33 with graphite shafts.
Designed to hit as easy as fairway woods with the
accuracy of irons.
Internal Sole Weighting lowers center of
gravity and helps give proper trajectory.
Made of 17-4 stainless with an attractive
black enamel finish.
Available in many lofts, from #1-9,
PW, SW in RH and LH to replace those harder to hit irons.
Numbered same as irons. See lofts in table
below. Also, club lengths are the same as irons.
Very reasonably priced:
CUSTOM ASSEMBLED with Std. steel, $25;
or
with iDrive graphite, only $33.
Recommended shafts are:
Apollo Acculite steel (93grms) or the high modulus graphite shafts like
the iDriver filament wound shafts.
Nice-fitting numbered
Mag. head covers (3-9, PW, SW) are available for just $3.00 each
with set order
below.
CALL to
Order
PP Select 5000 heads
at $13ea.
Call 970-209-6502 Cell
or 970-641-3822 to
order if desired or order securely online below.
Club
#1
#2
#3
#4
#5
#6
#7
#8
#9
PW
SW
Loft
15º
18
21
24
27
30
34
38
42
47
52
Lie
60º
60.5
61
61.5
62
62.5
63
63.5
64
64
64
Wt.
228gm
235
242
249
256
263
270
277
284
291
296
Std.Length (stl/grphte)
40"/
40.5"
39.5/
40
39/
39.5
38.5/
39
38/
38.5
37.5/
38
37/
37.5
36.5
/37
36/
36.5
36/
36.5
36/
36
Vol.
75cc
72
70
70
70
70
70
70
70
70
70
SET OFFER-From
only $23 each IN A SETS OF 6 or
more PP SELECT 5000 UTILITY IRONS. ONLY
$138
for any 6 assembled with std. steel; $186
for any 6 with quality iDrive graphite shafts or Apollo Acculite steel
shafts! Order below.
Select 5000 Sets with better grade shafts
Shaft Flex desired
Grip Choice
Club Lengths
Choose: iDrive graphite or Apollo Acculite steel
Tell us the Club Numbers you want
Questions or comments?
*NEW for 2009*
AVATAR XMOI Ironwoods
INTRODUCTORY 20% OFF SALE
VERY FEW REMAIN--CALL to order.
A hybrid set that is truly transformative.
Long ironwood heads have a wider and shallower
face ht. for maximum forgiveness.
Progressively narrower sole through the wedges for
maximum game improvement and control.
All heads #3-#9 have a lower COG and maximum MOI
to get the ball airborne quickly.
The 3 wedges have a larger face area and higher
COG for more control of trajectory.
Due to the increased MOI, these Avatar ironwoods
have a 1º stronger loft
throughout.
Available in RH only with lofts from #3-PW, AW,
SW.
Std. iron lengths. Square face angle.
Beautiful blue to black enamel finish.
Head is 431 stainless steel.
Custom assembled with many steel and graphite
shafts available as well as grips.
Recommended shafts are:
Apollo Acculite steel (93grms) or the high modulus graphite shafts like
the iDriver filament wound shafts.
CALL to order loft combinations or shaft/grip
combinations listed below:
Sale priced from only $30
each for completely assembled individual club with std. steel shaft.
Call 970-209-6502 Cell
or 970-641-3822 to
order if desired.
Measurements
Face Length
Face Height
Girth
#6
3"
1.75"
6.2"
#9
3"
2"
6.0"
CALL to ORDER Custom Assembled
AVATAR XMOI
Ironwood Sets with std. STEEL shafts. (Example: 6 with std. steel shafts)
for only $168.
VERY NICE SLIP-ON HYBRID COVERS w.
TAGS:
#3-PW, AW, SW. ONLY $5 ea. WHEN ORDERED WITH
AN IRONWOOD SET.
No.
3
4
5
6
7
8
9
PW
AW
SW
Loft
21º
24
27
30
33.5
37
41
45
50
55
Lie
60º
60.5
61
61.5
62.5
63.5
64
64.5
64.5
64.5
OFFSet
4.8mm
4.3
3.8
2.8
1.8
1.3
1.3
1.3
.8
.3
Wt.
242g
249
256
263
270
277
284
292
291
298
CALL to ORDER Custom Assembled
AVATAR XMOI
Ironwood Sets with GRAPHITE shafts.(Example: 6 with std. graphite shafts)
for only $210.
NOTE: Apollo Acculite steel shafts
will substitute the iDrive graphite shafts at the same price.
Dynacraft
AVATAR LS Hyper Steel
Ironwoods
VERY FEW REMAIN--CALL
BEST solution for those who struggle
hitting a regular iron.
Avatar Launch Series (LS) Hybrid are the
perfect blend of size and head weighting.
With their
hardened nickel-alloy face
and low center of gravity, these ironwoods
yield the distances and
trajectory you dream about.
Wide soles and minimal bounce help you
make solid contact on any ground surfaces.
These clubs are excellent for chipping
and bunker shots.
Available in RH iron lofts from #3-9,
PW, AW, and SW. Assembled to std iron lengths.
Progressive offsets from 6mm in the #3 to 1mm in
SW help produce a slight draw. Most irons have this amount of offset.
Custom assembled with many shaft and
grip options.
Recommended shafts are:
Apollo Acculite steel (93grms) or the high modulus graphite shafts like
the iDriver filament wound shafts.
Order any combination of lofts.
Call 970-209-6502 Cell
or 970-641-3822 to
order if desired.
Molded neoprene covers
w. tags. Hybrid Cover,
Zipper Closures 3-Pw, A, Sw Best Quality. Only $5.75 Will fit hybrid heads up to 6"girth
2-PW, AW, SW. Fits All. Only $20 for the set of 10.